Metallurgical Asstracts on Light Metal and Alloys

vol.6

INDEX

No Title Author
1 On the Mechanism of Shear Spinning. M. Hayama
2 Effect of Si on Structures and Mechanical Properties of Chilled Castings of Al-2wt% Cr Alloys. R. Ichikawa
3 Effect of Fe and Si on Age Hardening Properties of Supersaturated Solid Solutions of Al-Zr Alloy by Rapid Solidification. R. Ichikawa
4 Supercooling in the Solidification of Al-Mn, Al-Cr, and Al-Zr Binary Alloys. R. Ichikawa
5 Studies on Chilled Castings of Al-Zr Alloys (II) Effect of Cu, Mg, Mn, Si and Zn on Age Hardening of Chilled Cast Al-1% Zr Alloy. R. Ichikawa
6 Annealing of Cold-rolled Aluminium Alloys Deviation from Annealing Curves and Annealing Data. T. Igarashi
7 Static Strain Aging of Al-Mg Alloys. H. Kaieda
8 Sliding of Grain Boundary in Bicrystal of High-purity Aluminium and Al-Cu Solid Solution during Plastic Deformation. M. Kato
9 Nucleation ofθ' Precipitates in an Al-4% Cu Alloy. H. Kimura
10 Excess Vacancies and the Nucleation of Precipitates in Aluminium-Silicon Alloys. H. Kimura
11 Study on Some Factors Affecting the Distribution of Pressure in Cold Rolling of Aluminium Plate Y. Matsuura
12 On the Grain Boundary Sliding of Aluminium Alloy Bicrystals during Tensile Test under Constant Stress while Heating at Temperature Increasing at a Constant Rate G. Mima
13 Some Investigations on Hydrostatic Bulging Test. M. Miyagawa
14 Bulging of Aluminium Pipes by Axial Compression. M. Miyagawa
15 On the Variation of Plastic Stress Concentration Factor. S. Miyano
16 The Influence of Ultrasonic Vibration on the Coefficient of Friction by Use of the Semi-circular Ring. M. Mizuno
17 Stress-Corrosion Cracking of Al-Zn-Mg Alloy Bi-and Bamboo Crystals. Y. Murakami
18 On the Distribution of Pores and Gases in Al-Si Eutectic Alloys S. Nishi
19 On the Elevation of Deep-drawability of Aluminium and Aluminium Alloys by Improvement of Their Textures. K. Okada
20 Studies on Growth Twin Crystals in Aluminum and Aluminum-base Alloys. Introduction to the Studies on the Growth Twin Crystals in Aluminum and Aluminum-base Alloys. S. Oya

Back to top

21 Studies on Growth Twin Crystals in Aluminum and Aluminum-base Alloys. (II) Theory of Origin and Multiplication of Growth Twin Crystals in Aluminum and Aluminum-base Alloys. S. Oya
22 Study on Warm Extrusion of Al and Its Alloys. J. Seino
23 Effect of Precoating with Lead on Coating of Steel with Aluminium by Hot Dipping. F. Seki
24 Vibrational Entropy Changes due to Point Defects in Linear Lattices. J. Takamura
25 Local Corrosion of Anodized Film in Prolonged Electrolysis of Aluminium. S. Ueda
26 Study on the Machinability of Aluminium Alloys (X) Effects of Heat Treatment on the Machinability of Aluminium Cast Alloys. S. Zaima
27 Untersuchung Uber die Zerspanbarkeit von Aluminium Legierungen (XI) Zerspanbarkeit von Aluminiumgusslegierungen LO-EX Als Kolbenmaterial. S. Zaima
28 Study on the Machinability of Aluminium Alloys (XII) On the Machining of Aluminium Cast Alloy AC4D S. Zaima
29 Study on the Machinability of Aluminium Alloys (XIII) Effects of Copper and Silicon on the Machinability of Copper Silumin. S. Zaima
30 Study on the Machinability of Aluminium Alloys (XIV) Effects of Tin on the Machinability of Al-Si Alloy Castings. S. Zaima
31 Study on the Mechanism of Cutting Aluminium (XIV) Some Contributions to the Surface Structure of Orthogonal Cut Aluminium. S. Zaima
32 Study on the Mechanism of Cutting Aluminium (XV) Effect of Cutting Conditions on Roughness of Machined Surface of Aluminium Alloys S. Zaima
33 Study on the Mechanism of Cutting Aluminium (XVI) Some Considerations on the Mechanism of Orthogonal Cutting of Aluminium Binary Alloys. S. Zaima
34 Study on Hot Machining of Some Hard-machining Aluminium Alloys (I) Some Experiments on the Facing of Aluminium-silicon Cast Alloys. S. Zaima

Back to top