INDEX

1	Influence of Current Density to Direct Reduction of TiO2 in Molten CaCl2	Ryosuke O. Suzuki	[Journal of Japan Institute of Metals, Vol. 72, No. 12(2008), pp. 916-920]
2	Synthesis of Ti-6Al-4V Alloy by the Electrolysis of Molten CaCl2+CaO	Ryosuke O. Suzuki	[Journal of Japan Institute of Metals, Vol. 72, No. 12(2008)921-927]
3	Improvement of Corrosion Resistance of Al-Mg-Si Aluminum Alloy 6063 by Selective Removal of Intermetallic Compound Phases	O. Seri	[J. Light Japan Inst. Metals, Vol. 58, No. 1, (2008), pp. 8-14]
4	Change in Fatigue Strength of Biomedical -Type Titanium Alloy through Heat Treatment Processes	M. Niinomi	[J. Society Mater. Sci., Japan, Vol. 57, No. 9, (2008), pp. 893-898]
5	Development of Allergy-free Titanium Alloys for Brass Instruments and Their Characteristics	M. Niinomi	[J. Japan Light Metals, Vol. 58, No. 11, (2008), pp. 604-610]
6	Effect of Silane Coupling Treatment on Mechanical Properties of Porous Pure Titanium Filled with PMMA for Biomedical Applications	M. Niinomi	[J. Japan Inst. Metals, Vol. 72, No. 10, (2008), pp. 839-845]
7	Mechanical Properties of Implant rods Made of Low-modulus -Type Titanium Alloy, Ti-29Nb-13Ta-4.6Zr, for Spinal Fixture	M. Niinomi	[J. Japan Inst. Metals, Vol. 72, No. 9, (2008), pp. 674-678]
8	Fatigue Behaviors of Ultra Fine Wires of -Type and -Type Titanium Alloys	T. Narushima	[Materials Transactions, Vol. 50, No. 7(2009), pp. 1713-1719]
9	Development of Fine-Grained Structure caused by Friction Stir Welding Process of a ZK60A Magnesium Alloy	Y. Motohashi	[Materials Transactions, Vol. 50, No. 3, (2009), pp. 610-617]
10	Bendability of Pre-Stretched Al-Mg-Si Alloy Sheets Affected by Alloy Composition	G. Itoh	[The Journal of Japan Institute of Light Metals, Vol. 58, No. 9(2008), pp. 443-448]
11	Semisolid Continuous Casting of AS41B Magnesium Alloy Using an Inclined Cooling Plate	T. Motegi	[International Journal of Cast Metals Research, Vol. 21, No. 1-4(2008), pp. 105-108]
12	Improvement of Forging Process and Product Quality by FEM Simulation Method Using a Simple Tensile Test	K. Kanazawa	[Proceedings of 4th International Conference on Recent Advances in Materials, Minerals & Environment (RAMM '09) & 2nd Asian Symposium on Materials & Processing (ASMP '09), (2009), pp. MT62-126]
13	Some Characteristics of AZ31/AZ91 Dissimilar Magnesium Alloy Deposit by Friction Surfacing	K. Katoh	[Journal of Materials Transactions, Vol. 49, No. 5(2008), pp. 1137-1141]
14	Fabrication of 6061 Aluminum Alloy / Al2O3P Composites by Friction Surfacing	K. Katoh	[Journal of Japan Institute of Light Metals, Vol. 58, No. 7(2008), pp. 299-304]
15	Effect of Filling Condition of Alumina Particle on Dispersibility of Particle by Friction Surfacing	K. Katoh	[Journal of Japan Institute of Light Metals, Vol. 59, No. 3(2009), pp. 114-120]
16	Precision Punching of 5052 Aluminum Alloy Sheets	N. Koga	[Journal of Japan Institute of Light Metals, Vol. 59, No. 9(2009)]
17	Transparent Behavior of Aluminum Nanoparticle Compacts at Microwave Frequencies	Y. Kagawa	[Journal of Applied Physics, Vol. 103, No. 9(2008), pp. 093105 1-5]
18	Structural Vacancies in Al-Pd-Mn Quasicrystal and its (1/1, 2/1-)AlPdMnSi Approximant Crystals: Positron Lifetime Studies	K. Kimura	[Philosophical Magazine, Vol. 88, No. 13-15(2008), pp. 1929-1934]
19	Thermoelectric Properties of Polygrained Icosahedral Al71-χ GaχPd20Mn9 (χ =0, 2, 3, 4) Quasicrystals	K. Kimura	[Journal of Applied Physics, Vol. 104(2008), pp. 073721-1-4]
20	Influence of Crystal Orientation and Surface Topography of Aluminum Substrate on Pore Nucleation of Anodic Porous Alumina	S. Ono	[J. Jpn. Inst. Light Metals, Vol. 58, No. 8(2008), pp. 375-380]

21	Electrodeposition of Hydroxyapatite on Alkali Treated Titanium	S. Ono	[Journal of the Society of Inorganic Materials, Japan, Vol. 16 (2009), pp. 28-36]
22	Structural Features of Anodic Oxide Films Formed on Aluminum Substrate Coated with Self-assembled Microspheres	S. Ono	[Corrosion Science, Vol. 51, (2009), pp. 1496-1500]
23	Joining of 1050 Aluminum Circular Tube and Holed Rib by Extrusion	M. Murata	[Journal of Japan Institute of Light Metals, Vol. 58, No. 6(2008), pp. 246-250]
24	Effect of Beating Angle on Incremental In-Plane Bending of Sheet Metal	M. Murata	[Journal of the Japan Society for Technology of Plasticity, Vol. 49, No. 569, (2008), pp. 579-583]
25	Transparentization of Tunnel-Etched Al Foil by Anodic Oxidation	H. Masuda	[Japanese Journal of Applied Physics, Vol. 48, 020218(2009)]
26	Strip Casting by a Vertical Type High Speed Twin Roll Caster	S. Kumai	[Aluminum Alloys (Proceedings of the 11th International Conference on Aluminum Alloys, 22-26 Sept., 2008, Aachen, Germany, Vol. 1, pp. 413-420]
27	Effect of Lubrication Conditions on Trapping Ratio in Cold Sheet Rolling O/W Emulsion	A. Azushima	[Journal of the JSTP, Vol. 50, No. 576 (2009-1), pp. 55-58]
28	Optimization of ECAP Process for Mg Alloy	A. Azushima	[Journal of the JSTP, Vol. 50, No. 578 (2009-3), pp. 237-241]
29	Metal Flow in Boss Forming	K. Kawai	[Advanced Technology of Plasticity 2008, (2008), pp. 1317-1328, ISBN 978-5708-152-5]
30	Role of Solute Atmosphere on the Texture Formation of Al-Mg Solid Solution during High-Temperature Uniaxial Compression Deformation	H. Fukutomi	[J. Japan Inst. Metals, Vol. 74, No. 1 (2009), 58-63]
31	Direct Measurement Procedure for Three-dimensional Local Crack Driving Force Using Synchrotron X-ray Microtomography	H. Toda	[Acta Materialia, .Vol. 56, (2008), pp. 6027-6039]
32	Change in Microstructure of Al-Si-Cu Casting Alloys during High-temperature Solution Treatment	H. Toda	[International Journal of Cast Metals Research, Vol. 21, No. 1-4(2008), pp. 114-118]
33	Growth Behavior of Hydrogen Micropores in Aluminum Alloys during High-temperature Exposure	H. Toda	[Acta Materialia, .Vol. 57, (2009), pp. 2277-2290]
34	Effect of Ultrasonic Melt Treatment on the Microstructure of A356 Aluminum Cast Alloys	Y. Tsunekawa	[International Journal of Cast Metals Research, Vol. 21 (2008), pp. 129-134]
35	Microstructure Refinement in Hypereutectic Al-Si Alloy by Compressive Torsion Processing	N. Kanetake	[Journal of Japan Society for Technology of Plasticity, Vol. 50, No. 577(2009), pp. 109-113]
36	Effect of Die Cavity Constraint on Foaming Behavior and Pore Morphology of Sheet Type Porous Aluminum	N. Kanetake	[Journal of Japan Institute of Light Metals, Vol. 59, No. 1(2009), pp. 7-12]
37	Formation and Osteoconductivity of Hydroxyapatite/ Collagen Composite Films Using a Thermal Substrate Method in Aqueous Solutions	M. Okido	[Mater. Trans., Vol. 50, No. 5(2009), pp. 1190-1195]
38	Wear Properties of Intermetallic Compound Reinforced Functionally Graded Materials Fabricated by Centrifugal Solid-particle and In-Situ Methods	Y. Watanabe	[Journal of Solid Mechanics and Materials Engineering, 2 No. 7, 842-853 (2008)]
39	Formation of Wear-induced Layer with Nanocrystalline Structure in Al-Al3Ti Functionally Graded Material	Y. Watanabe	[Acta. Mater., 56, No. 17, 4549-4558 (2008)]
40	Experimental Study on Springback of Magnesium Alloy AZ31B in Draw Bending	H. Takuda	[Proceedings of the 8th International Conference on Magnesium Alloys and Their Applications, WILEY-VCH Verlag GmbH & Co. KGaA, Weimar, (2009)]

41	Mechanical and Functional Properties of Porous Metals Fabricated by Spacer Method	M. Mabuchi	[MetFoam 2007: Porous Metals and Metallic Foams (2008), pp. 359-362]
42	Fluxless Joining of Aluminum Alloy to Steel by Laser Irradiation Method	T. Takemoto	[J. Light Metal Welding & Construction, Vol. 46, No. 7(2008), 300-308]
43	Ultrasonic Soldering of Aluminum under Liquidus Temperatures of Sn-Zn Solders	T. Takemoto	[Smart Processing Technology, Vol. 2(2008), 71-74]
44	Fabrication of Lotus-type Porous Al-Si Alloys Using Continuous Casting Technique	H. Nakajima	[Metallurgical and Materials Transactions A, Vol. 40A (2009), pp. 406-414]
45	Deformation Behavior of Wiring Metals during Ultrasonic Bonding	Y. Takahashi	[Proceeding of MATE 2008, Japan Welding Soc., Vol. 14, (2008), pp. 347-350]
46	Effects of Alloying Elements on Interfacial Properties of Dissimilar Joint of Aluminum Alloy and Steels	A. Hirose	[Smart Processing Technology, Vol. 2(2008), pp. 199-202]
47	The Effects of Iron Content and Cooling Rate on Microstructures and Tensile Properties of Ti-Fe-Cr-Al Quaternary System Alloys	M. Ikeda	[J. Japan Inst. Metals, Vol. 72, No. 12(2008), pp. 975-982]
48	Effect of Combined Plasma-carburizing and Deep-rolling on Notch Fatigue Property of Ti-6Al-4V Alloy	T. Takasugi	[Materials Science and Engineering A, Vol. 499, No. 1-2 (2009), pp. 482-488]
49	Cavitation during Grain-boundary-sliding Deformation in an AZ61 Magnesium Alloy	K. Higashi	[Materials Science and Engineering A, Vol. 497(2008), pp. 139-146]
50	Effects of Small Addition of Ge on the Microstructure of Precipitation and Fatigue Strength for Dilute Al-Si Alloy	T. Kanadani	[Aluminum Alloys, Their Physical and Mechanical Properties, Vol. 2, pp. 1589-1594, Proceeding of the 11th International Conference on Aluminum Alloys (ICAA 11), edited by J. Hirsch, B. Skrotzki and G. Gottstein, (2008), Wiley-VCH]
51	Aging Behaviors in AZ91D/Al18B4O33w Composite Fabricated by Squeeze Casting	G. Sasaki	[Mat. Trans., 49, 04 (2008), pp. 637-642]
52	Effects of Aging Treatment on the Bending Strength in AZ91D/Al18B4O33w Composite	G. Sasaki	[Mat. Trans., 49, 04 (2008), pp. 850-853]
53	Effects of Cooling Rate and Zr Addition on Microstructure Formation in Ti-(15, 20) at% Nb Alloys	K. Nakai	[The Proc. of the 17th IFHTSE Congress 2008]
54	Principles of Deformation in Single Crystals of Two Different Orientations Processed by Equal-Channel Angular Pressing	M. Furukawa	[Materials Science and Engineering A, Vol. 503(2009), pp. 21-27]
55	Development of Fatigue Testing Machine for Thin Sheet Specimen and Fatigue Test for Magnesium Single Crystal	S. Ando	["Zairyo", Vol. 58, No. 8(2009), pp. 703-708]
56	Orientation Dependence of Fatigue Fracture Behavior in Pure Titanium Single Crystals	S. Ando	["Zairyo", Vol. 58, No. 10(2009), in press]
57	Influence of Grain Size and Aging on Fatigue Behavior of AZ-type Magnesium Alloys	N. Ono	[Proc. Of 12th Int. Conf. on Fracture, Ottawa, CD-ROM(2009), pp. 1-10]
58	Transition of Acceleration Behavior and Life Time Prediction of Mg-Al Solution Hardened Alloys at around 0.6Tm	H. Sato	[Multiple Approach to Fracture of Materials, Components and Structure, 17th European Conference on Fracture, Brno, European Structural Integrity Society (ESIS), Czech Republic (2008), PP. 1103-1110]
59	Effects of Coat Insulating and Permeability on Molten Aluminum Alloy Temperature during Mold Filling in Expandable Pattern Casting Process	S. Koroyasu	[The 3rd China Lost Foam Casting International Conference, (2008), pp. 8-12]
60	Bulk Al Materials from Back Pressure Equal Channel Angular Consolidation of Mechanically Milled Particles	M. Kubota	[Materials Science Forum, Vols 584-586(2008), pp. 428-433]

61	Development of Titanium/ Zirconia Composite by Spark Plasma Sintering (SPS) Method for Artificial Hip Joint	K. Katahira	[Proceedings of 6th Asian-Australasian Conference on Composite Materials, Fukuoka, Japan, Sep. (2008)]
62	Partial Grain Refinement in Al-3%Cu Alloy during ECAP at Elevated Temperatures	H. Miura	[Materials Transactions Vol. 50, No. 1(2009)pp. 101 to 110]
63	Continuous Dynamic Recrystallization during the Transient Severe Deformation of Aluminum Alloy 7475	H. Miura	[Acta Materialia, 57(2009)153-162]
64	Novel Strengthening Method of Closed-Cell Aluminum Foams through Surface Treatment by Resin	K. Kitazono	[J. Mater. Proc. Tech., Vol. 209, (2009), pp. 3550-3554]
65	The Precipitation Process in an Al-Mg-Si Alloy and the Influence of Two-step Ageing	M. Takeda	[The Proceeding of JSSUME2008 (2008), pp. 160-163]
66	Quantitative Estimation of Microstructural Dependence of Creep Characteristics for 3003 Aluminum Alloy Sheets	S. Hirosawa	[Aluminum Alloys, Their Physical and Mechanical Properties, Vol. 2, (2008), pp. 1532-1538]
67	Formation of Deformation Band in 5083-O Aluminum Alloy Sheet Tensile-deformed at 318K	Y. Nakayama	[J. Japan Institute of Light Metals, Vol. 58, No. 12(2008), pp. 662-667]
68	Effect of DLC Coating on Deep Drawability of AZ31 Magnesium Alloy Sheet	S. Yoshihara	[Proceedings of the 25th International Manufacturing Conference, (2008), pp. 23-29]
69	Recycling of Mg-Al-Zn Based Alloy by Vacuum Distillation	M. Inoue	[Proceedings of the Third International Conference on Processing Materials for Properties (PMP-III), (2009), in print]
70	Thermal Conductivity of the Al-based Quasicrystals and Approximants	T. Takeuchi	[Z. Kristallogr. 224 (2009) pp. 35-38/ DOI 10.1524/zkri.2009.1094]
71	Fatigue Properties of DLC-Coated Ti-6Al-4V Alloy	T. Morita	[Transactions of the Japanese of Mechanical Engineers (series A), Vol. 74, No. 741(2008), pp. 693-699]
72	Surface Modification of Aluminum Alloys	T. Wada	[The 11th International Conference on Aluminum Alloys-ICAA 11, 22-26 September 2008, Aachen Germany]
73	Deformation and Texture Evolution during Differential Friction Rolling of Aluminum Sheet	H. Utsunomiya	[Steel Research International, 79 (2008), pp. 168-175]
74	Impact Tensile Properties in Al-Mg-Si Base Alloys for Automotive Use	K. Horikawa	[International Journal of Modern Physics B, Vol. 22, No. 9, (2008), pp. 1123-1128]
75	Hydroxyapatite-loaded Thick Anodized Titanium Films	M. Iwasaki	[Journal of The Surface Finishing Society of Japan, Vol. 59, No. 5, (2008), pp. 340-342]
76	Bioactivity of Anodized Titanium Films Loaded with Hydroxyapataite	M. Iwasaki	[Journal of The Surface Finishing Society of Japan, Vol. 60, No. 4, (2009), pp. 285-287]
77	Effect of External Constraint and Evolution from Ideal Orientation on Development of Rolling Texture in Pure Aluminum Single Crystal Having {100}<001> Orientation	K. Kashihara	[Proceedings of the 15th International Conference on Textures of Materials (ICOTOM-15), Pittsburgh, PA, USA, June 1-6, 2008, CD-ROM, Total 8 pages]
78	Butt Joining of Sheet by Shot Peening	Y. Harada	[Proceedings of International Conference of Shot Peening 2008(ICSP2008), (2008), pp. 35-40]
79	Cold Butt Joining of Light Metal Sheet by Shot Peeing	Y. Harada	[Modern Physics Letter-B (SCI), Vol. 22-31/32, (2008), pp. 6100-6105]
80	The Influence of Strain Path on Biaxial Compressive Behavior of AZ31 Magnesium Alloy	I. Shimizu	[Modern Physics Letters-B, Vol. 22, Issue 31/32 (2008), pp. 5844-5849]

81	Effects of Strain Rate, Temperature and Sheet Thickness on Yield Locus of AZ31 Magnesium Alloy Sheet	T. Naka	[Journal of Materials Processing Technology, Vol. 201, (2008), pp. 395-400]
82	Relationship between Hydrogen Absorption and Corrosion Behavior of Ti-6Al-4V Alloy Immersed in Acidic Fluoride Solutions	Y. Kawamura	[Materials Transactions, Vol. 50, No.5 (2009), pp. 1183-1189]
83	The Structure of Guinier-Preston Zones in an Mg-2at%Gd-1at%Zn Alloy Studied by Transmission Electron Microscopy	Y. Kawamura	[Materials Transactions, Vol. 49, No.1(2008), pp. 227-229]
84	Microstructure Evolutions of Rapidly-Solidified and Conventionally-Cast Mg97Zn1Y2 Alloys	Y. Kawamura	[Materials Transactions, Vol. 49, No. 5(2008), pp. 990-994]
85	The Fine-Grained Structure in Magnesium Alloy Containing Long-Period Stacking Order Phase	Y. Kawamura	[Materials Transactions, Vol. 49, No. 6(2008), pp. 1294-1297]
86	Microstructures and Mechanical Properties of Mg96Zn2Y2 Alloy Prepared by Extrusion of Machined Chips	Y. Kawamura	[Journal of Japan Institute of Light Metals, Vol. 58, No. 2(2008), pp. 54-57]
87	Microstructural Evolution in Pure Aluminum Processed by High-pressure Torsion	Z. Horita	[Materials Science and Engineering A, 503, (2009), pp. 32-36]
88	Using Ring Samples to Evaluate the Processing Characteristics in High-pressure Torsion	Z. Horita	[Acta Materialia, 57, (2009), pp. 1147-1153]
89	Scaling-Up of High Pressure Torsion Using Ring Shape	Z. Horita	[Materials Transactions, 50, (2009), pp. 92-95]
90	Development of High-pressure Sliding for Microstructural Refinement of Rectangular Metallic Sheets	Z. Horita	[Materials Transactions, 50, (2009), pp. 930-933]