INDEX

1	Direct Production of Ti-29Nb-13Ta-4.6Zr Biomedical Alloy from Oxide Mixture in Molten CaCl2	Ryosuke O. Suzuki	[Journal of the Electrochemical Society, Vol. 157, No. 8(2010), pp. E117-E121]
2	Corrosion Phenomenon and its Analysis of 6063 Al-Mg-Si Alloy in Ethyl Alcohol	O. Seri	[J. Light Japan Inst. Metals, Vol. 59, No. 7, (2009), pp. 359-364]
3	Strengthening of Lamellar TiAl Alloys by Precipitation Bands of βo Particles	K. Maruyama	[Materials Science and Engineering A, Vol. 510-511(2009), 14-19]
4	Quality Improvement of a β-Type Titanium Alloy Cast for Biomedical Applications by Using a Calcia Mold	M. Niinomi	[Mater. Trans. Vol. 51, No. 1(2010), pp. 128-135]
5	Effect of Oxygen Content on Microstructure and Mechanical Properties of Biomedical Ti-29Nb-13Ta-4.6Zr Alloy under Solutionized and Aged Conditions	M. Niinomi	[Mater. Trans. Vol. 50, No. 12(2009), pp. 2716-2720]
6	Development of Biomedical Porous Titanium Filled with Medical Polymer by In-situ Polymerization of Monomer Solution Infiltrated into Pores	M. Niinomi	[Mech. Behav. Biomed. Mater., Vol. 3, No. 1(2010), pp. 41-50]
7	Mechanical Properties of Implant Rods Made of Low-Modulus β-Type Titanium Alloy, Ti-29Nb-13Ta-4.6Zr, for Spinal Fixture	M. Niinomi	[Ceramic Transactions, Vol. 206, (2009), pp. 83-90]
8	The High-Precision Machining by Ultra Sonic Vibration Cutting Method with Using Lower-Young's Tool	T. Furusawa	[Proceedings of Symposium on Ultrasonic Electronics, Vol. 30(2009), pp. 7-8]
9	Optimization of Tribological and Fatigue Characteristics for Magnesium Alloy with DLC/FPB Combined Surface Treatment	H. Suzuki	[Proceedings of The Fourth Asian Conference on Heat Treatment and Surface Engineering October 27-30, 2009, Beijing, China, pp. 486-490]
10	Thermoelectric Performance of Al-Pd-Mn Quasicrystals: Comparison with (1/1, 2/1-)AlPdMnSi Approximants and Improvement by Ga Substitution for Al	K. Kimura	[Zeitschrift für Kristallographie, Vol. 224(2009), pp. 21-25]
11	Thermoelectric Properties of Al-Pd-Re Quasicrystal Sintered by Spark Plasma Sintering (SPS): Effect of Improvement of Microstructure	K. Kimura	[Zeitschrift für Kristallographie, Vol. 224(2009), pp. 79-83]
12	Structure and Growth Mechanism of Anodic Oxide Films Formed on Aluminum and Their Gas Emission	S. Ono	[J. Vac. Soc. Jpn, Vol. 52(2009), pp. 637-644]
13	Bioactivation of Titanium Surfaces Using Coatings of TiO2 Nanotubes Rapidly Pre-loaded with Synthetic Hydroxyapatite	S. Ono	[Acta Biomaterialia, Vol. 5, (2009), pp. 2322-2330]
14	Deformation in V-bending of Aluminum Alloy 5083 Plate	M. Murata	[Journal of Japan Institute of Light Metals Vol. 60-6(2010), 264-268]
15	Fabrication of AZ31 Magnesium Alloy Fine Tubes by Dieless Drawing Process	K. Manabe	[in Press, Journal of Japan Society for Technology of Plasticity, Vol. 51, No. 597(2010)]
16	Fabrication of Au Fine Structures of Nanoparticles by Anodization of Purple Gold (AuAl2)	H. Masuda	[Chemistry Letters, Vo. 38, No, 12(2009), pp. 1148-1149]
17	Re-examination of Creep Behaviour on High Purity Aluminium in Low Temperature	E. Sato	[ICSMA 15 (15th International Conference on the Strength of Materials), 2009, Dresden ]
18	Measurement and Analysis of Inlet Oil Film Thickness in Cold Sheet Rolling with Oil in Water Emulsion	A. Azushima	[Tribology Transactions, 52, 2009, 427-434]
19	Starvation Behavior in Cold Rolling of Aluminum with Oil-in Water Emulsion	A. Azushima	[Tribology Transactions, 52, 2009, 744-749]
20	Effect of Silver Addition on the β'-phase in Al-Mg-Si-Ag Alloy	S. Ikeno	[The Materials Transactions, Vol. 51, No. 2(2010), pp. 310-316]
21	Effect of Cu or Ag Addition on Precipitation Sequence in Al-Mg2Si Alloys Containing Mg in Excess	S. Ikeno	[The Journal of the Japan Institute of Light Metals, Vol. 60, No. 4(2010), pp. 164-169]
22	Roles of Pre-Existing Hydrogen Micropores on Ductile Fracture	H. Toda	[Materials Transactions, Vol. 50, No. 9, (2009), pp. 2285-2290]
23	Three-dimensional Fatigue Crack Growth Behavior in an Aluminum Alloy Investigated with In Situ High-resolution Synchrotron X-ray Microtomography	H. Toda	[Acta Materialia, Vol. 57, (2009), pp. 3287-3300]
24	Healing Behavior of Preexisting Hydrogen Micropores in Aluminum Alloys during Plastic Deformation	H. Toda	[Acta Materialia, Vol. 57, (2009), pp. 4391-4403]
25	Influence of High-temperature Solution Treatments on Mechanical Properties of an Al-Si-Cu Aluminum Alloy	H. Toda	[Acta Materialia, Vol. 58, (2010), pp. 2014-2025]
26	Solid State Recycling of Aluminum Machined Chip Wastes by Compressive Torsion Processing	N. Kanetake	[Journal of Japan Institute of Light Metals, Vol. 59, No. 7(2009), pp. 354-358]
27	Effect of Thermal Condition on Blowing Behavior and Pore Morphology of Porous Magnesium	N. Kanetake	[Journal of Japan Institute of Light Metals, Vol. 59, No. 5(2009), pp. 261-264]
28	Synthesis of Porous Al3Ti/Al Composite and Effect of Precursor Processing Condition on Porous Structure and Compressive Properties	N. Kanetake	[Materials Transaction, Vol. 50, No. 11(2009), pp. 2609-2614]
29	Behavior of a Submicrocrystalline Aluminum Alloy 1570 under Conditions of Cyclic Loading	Y. Watanabe	[The Phys. Met. Metall., 107, No. 3, 291-297(2009)]
30	A Novel Fabrication Method for Functionally Graded Materials under Centrifugal Force: The Centrifugal Mixed-Powder Method	Y. Watanabe	[Materials, 2, 2510-2525(2009)]
31	Anisotropic Mechanical Properties of ECAPed Al-5%Zr Containing Platelet Particles	Y. Watanabe	[Mater. Sci. Eng. A, 527, 4674-4679(2010)]
32	Springback Characteristics of Magnesium Alloy Sheet AZ31B in Draw-Bending	H. Takuda	[Material Transactions, 51-4(2010), pp. 685-693]
33	Fabrication of Lotus-type Porous Aluminum through Thermal Decomposition Method	H. Nakajima	[Metallurgical and Materials Transactions A, Vol. 40A, (2009), pp. 937-942]
34	Relation between Vibration of Wedge-Tool and Adhesion of Wire to Substrate during Ultrasonic Bonding --- Monitoring of Al Ultrasonic Bonding Behavior ---	Y. Takahashi	[J. of Japan Welding Society, Vol. 27, No. 2, (2009), pp. 200s-203s]
35	Selective Dissolution of Nano Lamellar Ti-41 at.% Al Alloy Single Crystals	Y. Minamino	[Acta Materialia, Vol. 58, (2010), 2876-2886]
36	Characteristics and Estimation of Interfacial Microstructure with Additional Elements in Dissimilar Joints of Aluminum Alloys to Steel	A. Hirose	[Quarterly Journal of The Japan Welding Society, Vol. 27(2009), pp. 174s-178s]
37	Evaluation of Contact Properties of MEMS Probe for Al Electrode	K. Uenishi	[Microjoining and Assembly Technologies for Electronics, Vol. 15(2009), p. 259-262]
38	Formation of New Bone with Preferentially Oriented Biological Apatite Crystals Using Novel Cylindrical Implant Containing Anisotropic Open Pores Fabricated by Electron Beam Melting Method	T. Nakano	[Tetsu-to-Hagane, Vol. 96, No. 9(2010), pp. 42-48]
39	Isothermal Aging Behavior of Beta Titanium-Manganese Alloys	M. Ikeda	[Materials Transactions, Vol. 50, No. 12(2009), pp. 2737-2743]
40	Effects of Combined Plasma-carburizing and Shot-peening on Fatigue and Wear Properties of Ti-6Al-4V Alloy	T. Takasugi	[Surface and Coatings Technology, Vol. 203, (2009), pp. 1400-1405]
41	Investigation on Dynamic Friction Properties of Extruded AZ31 Magnesium Alloy Using by Ring Upsetting Method	K. Higashi	[Materials Transactions, Vol. 51, No. 7(2010), pp. 1249-1254]
42	High Rate Performance of Aerosol-deposited Mg2Ge Alloy Anode in Lithium Batteries	T. Esaka	Eloctrochemistry, Vol. 78. No. 7(2010), pp. 611-614
43	Investigation of Tensile-Compressive Yield Asymmetry in Extruded Pure Magnesium	T. Yokoyama	[International Journal of Materials Research, 101, (2010), pp. 736-740]
44	Distribution of Hydride in Titanium Determined by X-Ray Diffraction-Enhanced Imaging Method with Asymmetric Reflection Analyzer	K. Mizuno	[Transaction of the Materials Research Society of Japan, Vol. 34, No. 2(2009), pp. 229-232]
45	Precipitation of β' Phase in a Low Cost Beta Titanium Alloy	K. Nakai	[Materials Science Forum, Vols. 638-642, (2010), pp. 461-464]
46	Effect of Quenching and Reheating on Isothermal Phase Transformation in Ti-15Nb-10Zr Alloy	K. Nakai	[Materials Science Forum, Vols. 638-642, (2010), pp. 582-587]
47	The Morphology of Precipitations Al-Mg-Si-Sc-Zr Hot Rolled Sheet	H. Nakashima	[Materia Japan, Vol. 48, (2009), p. 611]
48	Microstructures of Aluminum and Copper Single Crystals Processed by Equal-Cannel Angular Pressing	M. Furukawa	[Materials Science Forum, Vols. 639-642(2010), pp.  1946-1951]
49	Deformation Behavior of Magnesium Single Crystal in C-axis Compression and A-axis Tension	S. Ando	[Materials Science Forum, Vols. 654-656(2010), pp. 699-702]
50	Evaluation of Particle Size and Shape Distributions in Al-Al3Ni Functionally Graded Materials Fabricated by a Semi-solid Forming Process	Y. Fukui	[Int. J. Mater. Product Tech., Vol. 39, Nos. 1/2(2010), pp. 108-121]
51	Mechanically Alloyed and Spark Plasma Sintered Aluminum/ Precious Metal Oxide Composite Materials	M. Kubota	[Materials Science Forum, Vols. 638-642(2010), pp. 1824-1829]
52	Anisotropy of Low Temperature Superplasticity of Fine Grained Magnesium Alloy AZ31 Processed by Multidirectional Forging	H. Miura	[Materials Science and Technology, Vol. 25(2009), pp. 1442-1447]
53	Temperature Effect on Fine-grained Structure Formation in High-strength Al Alloy 7475 during Hot Severe Deformation	H. Miura	[Materials Science and Engineering A 516(2009), 180-188]
54	Effect of Preheating Temperature on ECAP Formability of AC4CH Aluminum Casting Alloy	Y. Nakayama	[Materials Transactions, Vol. 51, No. 5(2010), pp. 918-924]
55	Microstructure Evolution of AZ31B Magnesium Alloy Pre-Strained by Torsion Working during Warm Compressive Deformation	M. Furui	[Magnesium, Proceedings of 8th International Conference on Magnesium Alloys and Their Applications, Edited by K. U. Kainer, (2009), pp. 326-330]
56	Recycling from Mg-Al-Zn System Alloy to High-purity Mg-Zn Alloy by The Vacuum Distillation Method	M. Inoue	[J. Japan Institute of Light Metals, Vol. 59, No. 11(2009), pp. 637-641]
57	A Proposal and an Untouched Subject of Standardization of Impact Compression Test by Split Hopkinson Pressure Bar Technique — Study on Standardization of Impact Compression Test by Split Hopkinson Pressure Bar Technique with the Aid of Numerical Simulation 3 —	M. Yamashita	[J. Japan Society for Technology of Plasticity, Vol. 50, No. 584(2009), pp. 842-846]
58	Cutting Performance of Diamond-Like Carbon Coated Tool in Cutting of Aluminum Alloys	T. Wada	[Materials Science Forum, Vols. 638-642(2010), pp. 368-373]
59	Effects of Traces of Sodium and Strain Rate on Grain Boundary Microstructures in Al-5mass% Mg Alloys Deformed at Elevated Temperatures	K. Horikawa	[Materials Transactions, Vol. 50, No. 12, (2009), pp. 2790-2794]
60	Characteristics of Strain-induced Boundary Migration as Evaluated by the Crystal Rotation Axis Method in (001)[100] and (112)[111] Aluminum Bicrystal Deformed by Plane-strain Compression	K. Kashihara	[Materials Transactions, Vol. 51, No. 4(2010), pp. 607-613]
61	Forming of Deep Container Used Developed Blank of Aluminum Sheet with Mechanical Joint of Sidewall	N. Hatanaka	[The Japan Institute of Light Metals, Vol. 59, No. 12(2009), pp. 672-677]
62	Mechanical and Thermal Properties of Vapor-Grown Carbon Fiber Reinforced Aluminum Matrix Composites by Plasma Sintering	G. Sasaki	[Materials Transactions, 51, 3(2010), 510-515]
63	Superplastic Flow in a Nanostructured Aluminum Alloy Produced Using High-pressure Torsion	Z. Horita	[Materials Science and Engineering A, 500, (2009), pp. 170-175]
64	Processing Pure Ti by High-pressure Torsion in Wide Ranges of Pressures and Strain	Z. Horita	[Metallurgical and Materials Transactions A, 40, (2009), pp. 2079-2086]
65	Microstructural Evolution in Pure Aluminum in the Early Stages of Processing by High-pressure Torsion	Z. Horita	[Materials Transactions, 51, (2010), pp. 2-7]
66	Universal Plot for Hardness Variation in Pure Metals Processed by High-pressure Torsion	Z. Horita	[Materials Transactions, 51, (2010), pp. 1051-1054]