| 1 |
Protection of an AZ91D Substrate by an Intermediate Zn Layer for Al Plating from an AlCl3-NaCl-KCl Molten Salt Bath |
K. Azumi |
[Surface & Coatings Technology 270, 164-169(2015)] |
| 2 |
Extrapolation of Creep Curve and Creep Rate by Strain Acceleration Parameter in Al-Mg Solid Solutions |
H. Sato |
[Materials Science Forum Vols. 794-796(2014), pp. 307-312] |
| 3 |
Evaluation of Thin Amorphous Calcium Phosphate Coatings on Titanium Dental Implants Deposited Using Magnetron Sputtering |
T. Narushima |
[Implant Dentistry, Vol. 23, No. 3(2014), pp. 343-350] |
| 4 |
Behavior of Hydrogen in a Tensile-deformed Al-Mg Alloy |
G. Itoh |
[J. Japan Inst. Met. Mater., Vol. 79, No. 3(2015), pp. 137-141] |
| 5 |
Effect of Hot Forging Condition on the Microstructure Formation Process in a 6061 Aluminum Alloy |
G. Itoh |
[Journal JILM, Vol. 65, No. 4(2015), 123-130] |
| 6 |
Texture Evolution in Aluminum Sheet Subjected to Friction Roll Surface Processing and Subsequent Annealing |
Y. Takayama |
[Materials Transactions, Vol. 56(2015), pp. 303-312] |
| 7 |
Springback of Aircraft Sheet Metal Hydro-Pressure and Stretch Forming Methods |
S. Takahashi |
[Journal of Material Science and Engineering A4(9)(2014), pp. 259-265] |
| 8 |
Properties of Upgradable Recycled Al-Mg-Si Alloys Fabricated from Machined Chips Via Mechanical Milling and Spark Plasma Sintering |
M. Kubota |
[Journal of Japan Institute of Light Metals, Vol. 64, No. 2(2014), pp. 37-41] |
| 9 |
Image-based Finite Element Analysis of Porous Aluminum and its Accuracy Examination |
T. Utsunomiya |
[Journal of The Japan Institute of Light Metals, Vol. 64, No. 11(2014), pp. 551-556] |
| 10 |
Nondestructive Observation of Compression Behavior of Pores in Three-layered Functionally Graded Aluminum Foam of A1050/A6061/ADC12 by X-ray Computed Tomography |
T. Utsunomiya |
[Journal of The Japan Institute of Light Metals, Vol. 64, No. 11(2014), pp. 587-592] |
| 11 |
Thermoelectric Properties of Al-Ga-Pd-Re Icosahedral Quasicrystals |
K. Kimura |
[Materials Transactions, Vol. 55(2014), pp. 1226-1231] |
| 12 |
Detection of Crack Propagation by AE and Evaluation of Fracture Toughness in Various Mg Alloys |
M. Enoki |
[J. Japan Inst. Met. Mater., Vol. 78, No. 10(2014), pp. 381-387] |
| 13 |
Joint Interface Microstructure of A4045/A3003/A4045 Alloy Clad Strips Fabricated by Vertical-type Tandem Twin-roll Casting |
S. Kumai |
[Journal of Japan Foundry Engineering Society, Vol. 86, No. 3(2014)pp. 223-228] |
| 14 |
Microstructure and Mechanical Properties of 4045/3003/4045 Aluminum Alloy Clad Sheet Fabricated by Vertical-type High-speed Tandem Twin-roll Casting |
S. Kumai |
[Journal of the Japan Institute of Light Metals, Vol. 64, No. 9(2014)pp. 399-406] |
| 15 |
Formability Improvement by Die-bearing Grooves in Tube Extrusion with Spiral Inner Projections |
T. Kuboki |
[Science Direct, Procedia Engineering, 81(2014), 641-646] |
| 16 |
Ideally Ordered Porous TiO2 Prepared by Anodization of Pretextured Ti by Nanoimprinting Process |
H. Masuda |
[Electrochem. Commu., Vol. 50(2015), pp. 73-76] |
| 17 |
Development of Extrusion-Torsion Simultaneous Processing for Grain Refinement and Texture Randomizing in Magnesium Alloys |
M. Furui |
[Materials Science and Engineering, Vol. 63(2014), pp. 1-5] |
| 18 |
Enlargement of Surface Area of Al by Electrochemical Insertion and Deinsertion of Li |
K. Nishio |
[Electrochemistry Communications, Vol. 59, (2015), pp. 13-15] |
| 19 |
Creep Mechanism in Several Grades of Aluminum at Low Temperatures |
E. Sato |
[KEIKINZOKU, Vol 64, No. 2(2014), pp. 42 to 48] |
| 20 |
Microstructural Control of Ti-46Al-7Nb-0.7Cr-0.2Ni-0.1Si Alloy by Heat Treatment |
H. Fukutomi |
[International Journal of Materials Research, Vol. 105, (2014), pp. 1075-1083] |
| 21 |
Comparative and Complementary Characterization of Precipitate Microstructures in Al-Mg-Si(-Li) Alloys by Transmission Electron Microscopy, Energy Dispersive X-ray Spectroscopy and Atom Probe Tomograpgy |
H. Hirosawa |
[Journal of Alloys and Compounds, Vol. 622, (2015), pp. 765-770] |
| 22 |
Effect of Dynamic Strain Rate on Micro-indentation Properties of Pure Aluminum |
N. Ogasawara |
[Accepted in Proceedings of 11th International DYMAT Conference 2015] |
| 23 |
Effects of Short Time Solution Treatment at High Temperature Using Induction Heating Apparatus on Mechanical Properties in JIS AC4CH Alloys |
Y. Nakayama |
[Journal of Japan Foundry Engineering Society, Vol. 86, No. 7, pp. 523-530(2014)] |
| 24 |
Precipitation Sequence in the Mg-Gd-Y System Investigated by HRTEM and HAADF-STEM |
K. Matsuda |
[Journal of Materials Transactions, Vol. 55, No. 7(2014), pp. 1051-1057] |
| 25 |
Energy Absorption Performance of Press-Formed Shell |
M. Yamashita |
[Procedia Engineering, Vol. 81(2014), 951-956] |
| 26 |
Hydrothermal Treatment of Titanium Alloys for the Enhancement of Osteoconductivity |
M. Okido |
[Materials Science and Engineering C, 49, (2015), pp. 430-435] |
| 27 |
Fabrication of Grain Refined Functionally Graded Grinding Wheel Reinforced by Composite Particles and its Application for Drilling CFRP |
Y. Watanabe |
[Journal of Functionally Graded Materials, 28, 1-8(2014)] |
| 28 |
Grain Refinement of Aluminum Casting Alloy by Heterogeneous Nucleation Sites with Smaller Lattice Disregistry |
Y. Watanabe |
[Journal of The Japan Institute of Light Metals, 64, No. 4, 157-163(2014)] |
| 29 |
Grain Refinement of Al Cast by Novel Al-Al2.5C0.5Ti Refiner Fabricated by Cold Pressing |
Y. Watanabe |
[Mater. Sci. Forum, 783-786, 276-281(2014)] |
| 30 |
Color Tone and Interfacial Microstructure of White Oxide Layer on Commercially Pure Ti and Ti-Nb-Ta-Zr Alloys |
Y. Watanabe |
[Jpn. J. Appl. Phys., 53, No. 11, 11RD02(8 pages) (2014)] |
| 31 |
Grain Refinement of Al3Ti Dispersed Aluminum Matrix Composites by Reaction Centrifugal Mixed-Powder Method |
Y. Watanabe |
[Materials Transactions, 56, No. 1, 99-107(2015)] |
| 32 |
Distribution of Microstructure and Cooling Rate in Al-Al2Cu Functionally Graded Materials Fabricated by a Centrifugal Method |
Y. Watanabe |
[J. Mater. Proc. Tech., 221, 197-204(2015)] |
| 33 |
Microstructure and Mechanical Properties of AZ61Mg Alloy Fabricated by Multi-Directional Forging Using Die under Decreasing Temperature Conditions |
H. Miura |
[J. Japan Inst. Met. Mater. Vol. 79, No. 6(2015), pp. 295-302] |
| 34 |
Room-Temperature Multi-Directional Forging of AZ80Mg Alloy to Induce Ultrafine Grained Structure and Specific Mechanical Properties |
H. Miura |
[Procedia Engineering, Vol. 81(2014), pp. 534-539] |
| 35 |
Thermoelectric Properties of Al-Mn-Si C40 Phase Containing Small Amount of W or Ta |
T. Takeuchi |
[Jpn. J. Appl. Phys. 54(7), 071801. (2015)] |
| 36 |
Deformation Behavior of a Magnesium Alloy Sheet with Random Crystallographic Orientations |
H. Takuda |
[Key Engineering Materials, 611-612(2014), 27-32] |
| 37 |
Formation of Interfacial Microstructure of a Friction Stir Welded Lap Joint between Aluminum Alloy and Stainless Steel |
A. Hirose |
[Science and Technology of Welding and Joining, Vols. 19(2014), pp. 609-616] |
| 38 |
Novel Powder/Solid Composites Possessing Low Young’s Modulus and Tunable Energy Absorption Capacity, Fabricated by Electron Beam Melting, for Biomedical Applications |
T. Nakano |
[Journal of Alloys and Compounds, Vol. 639(2015)336-340] |
| 39 |
Interfacial Deformation and Friction Heating in Ultrasonic Al Ribbon Bonding |
Y. Takahashi |
[IOP, Conf. Series: Materials Science and Engineering, Vol. 61(2014), 012004, pp. 1-8] |
| 40 |
Phase Constitution and Aging Behavior of Ti-10mass% Mn-Oxygen Alloys |
M. Ikeda |
[Proceedings of Ti-2015, December, 2015] |
| 41 |
Dislocation Creep in Al-22.2, 53.6 and 101 at.ppm Fe Solid Solution Alloys |
K. Higashi |
[Advanced Materials Research, Vol. 922(2014), pp. 749-754] |
| 42 |
Formability of Pure Titanium Sheet in Square Cup Deep Drawing |
Y. Harada |
[Procedia Engineering, Vol. 81,2014, pp. 881-886] |
| 43 |
Improvement of Formability for Multistage Deep Drawing of Ti-15V-3Cr-3Sn-3Al Alloy Sheet |
Y. Harada |
[Procedia Engineering, Vol. 81,2014, pp. 819-824] |
| 44 |
Fabrication of Aluminum-Graphite Composites by Hot Extrusion |
Z. -C. Chen |
[Journal of Materials and Metallurgy, Vol. 14, No. 3(2015), pp. 227-231] |
| 45 |
Effect of Dispersibility of TiB2 Particle on Electrical Conductivity in TiB2/Al Composites |
G. Sasaki |
[Materials Science Forum, 783-786(2014), pp. 1573-1578] |
| 46 |
Nano-Level Surface Processing of Fine Particles by Cavitation to Improve the Photocatalytic Properties of Titanium Oxide |
T. Yoshimura |
[Journal of Nanoscience & Nanotechnology-Asia, 2014, Vol. 4, No. 1(2014), pp. 69-78] |
| 47 |
Application of High-pressure Torsion to Al-6%Cu-0.4%Zr Alloy for Ultrafine-grain Refinement and Superplasticity |
Z. Horita |
[Journal of Materials Science, 49(2014), pp. 6689-6695] |
| 48 |
Softening by Severe Plastic Deformation and Hardening by Annealing of Aluminum-Zinc Alloy: Significance of Elemental and Spinodal Decompositions |
Z. Horita |
[Materials Science and Engineering A, 610(2014), pp. 17-27] |
| 49 |
Influence of Severe Plastic Deformation at Cryogenic Temperature on Grain Refinement and Softening of Pure Metals: Investigation Using High-Pressure Torsion |
Z. Horita |
[Materials Science and Engineering A, 613(2014), pp. 103-110] |
| 50 |
Grain Refinement and High Strain Rate Superplasticity in Aluminum 2024 Alloy Processed by High-pressure Torsion |
Z. Horita |
[Materials Science and Engineering A, 622(2015), pp. 139-145] |
| 51 |
Strengthening of AA7075 Alloy by Processing with High-pressure Sliding (HPS) and Subsequent Aging |
Z. Horita |
[Materials Science and Engineering A, 628(2015), pp. 56-61] |
| 52 |
Effect of Thermo-mechanical Treatment on Ridging Behavior and Cube-oriented Grain Formation Process in 6111 Aluminum Alloy |
H. Nakashima |
[Journal of The Japan Institute of Light Metals, Vol. 64, No. 8(2014), pp. 353-360] |
| 53 |
Formation Behaviour of a Blister in Cast Aluminum Alloy |
H. Toda |
[International Journal of Cast Metals Research, Vol. 27, No. 6(2014), pp. 369-377) |
| 54 |
Development of Teaching Material for Effect of Sectional Dimensions of Bars on Bending Strength |
M. Furukawa |
[Journal of the Japan Society of Technology Education in Kyushu Branch, Vol. 22(2014), pp. 1-7] |
| 55 |
Evaluation of the Deformation Behavior of a Semi-solid Hypereutectic Al-Si Alloy Compressed in a Drop-Forge Viscometer |
Y. Fukui |
[Metall. and Mater. Trans. A, Vol. 46A, May(2015), pp. 1908-1916] |
| 56 |
Influence of Semi-Solid Compression Conditions on the Refinement of Si Particles in Hypereutectic Al-25mass% Si Alloy |
Y. Fukui |
[Multidisciplinary Engineering and Technology, Vol. 2(2015), pp. 172-179] |
| 57 |
Effect of the Near-net Shape Forming on Silicon Morphology in an Al-Si Functionally Graded Material Generated by the Centrifugal Method |
Y. Fukui |
[Int. J. Materials Science and Applications, Vol. 4, (2015), pp. 12-19] |
| 58 |
Evaluation of Metal Cation Effects on Galvanic Corrosion Behavior of the A5052 Aluminum Alloy in Low Chloride Ion Containing Solutions by Electrochemical Noise Impedance |
M. Sakairi |
[Electrochimica Acta, 131(2014), pp. 123-129] |
| 59 |
Rapid Reduction of Titanium Dioxide Nano-particles by Reduction with a Calcium Reductant |
T. Kikuchi |
[Journal of Physics and Chemistry of Solids, 75(2014)1041-1048] |
| 60 |
Controllable Fabrication of Networked Three-Dimensional Nanoporous Anodic Alumina Films on Low-Purity Al Materials |
S. -Z. Kure-Chu |
[Journal of The Electrochemical Society, Vol. 162, No. 1(2015), pp. C24-C34] |
| 61 |
Local Melting in Al Embedded with TiNi Powder Induced by Microarea Self-propagating High-temperatures Synthesis |
T. Yamamoto |
[Philosophical Magazine, Vol. 94, No. 28(2014), pp. 3234-3246] |
| 62 |
Effect of Melt Velocity on Density of Aluminum Alloy Casting in Expendable Pattern Casting Process |
S. Koroyasu |
[Transactions of the 20th Anuual Conference on Lost Foam, V Method and Full Mold Casting Technology in China, (2014), pp. 23-29] |
| 63 |
Effect of Pre-aging Period on the Formation Behavior of Nanoclusters in Al-Mg-Cu Alloy |
E. Kobayashi |
[Materials Transactions, Vol. 56, No. 4, pp. 500-506, 2015] |
| 64 |
Preparation of Corrosion Resistant Film on Magnesium Alloy by Steam Coating |
T. Ishizaki |
[Journal of The Japan Institute of Light Metals, Vol. 64, No. 12(2014), 638-642] |
| 65 |
Enhanced Ductility at Room Temperature of Mg-9%Al-1%Zn Alloy Plate after Hot Pressing |
K. Kitazono |
[Journal of The Japan Institute of Light Metals, Vol. 65, No. 2(2015), pp. 61-65] |
| 66 |
TiO2 Hollow Spheres with Nanoporous Structures Fabricated by Anodization of Ti Particles |
T. Yanagishita |
[RSC Adv., Vol. 5(2015), pp. 41830-41834] |
| 67 |
Morphology and Thermal Stability of Metastable Precipitates Formed in an Al-Mg Alloy Aged at 373K and 473K |
M. Takeda |
[Applied Mechanics and Materials Journal Vols. 799-800(2015), pp. 212-216] |
| 68 |
Ductility Loss of 7075 Aluminum Alloys Affected by Interaction of Hydrogen, Fatigue Deformation, and Strain Rate |
H. Yamada |
[Materials Science and Engineering A, Vol. 642(2015), pp. 194-203] |
| 69 |
Discontinuous Precipitation Behavior and Microstructure in Mg-Al System Alloys |
C. Watanabe |
[Journal of the Japan Institute of Light Metals, Vol. 64, No. 10(2014), pp. 470-475] |
| 70 |
Effect of External Stress on Nucleation of Ellipsoidal ω Precipitates in a Ti-20wt%Mo Alloy |
C. Watanabe |
[Journal of Materials Science, Vol. 50(2015), pp. 1876-1882] |
| 71 |
Effect of Combination Treatment on Wear Resistance and Strength of Ti-6Al-4V Alloy |
T. Morita |
[Materials Science & Engineering A, Vol. 618(2014), pp. 438-446. 595] |
| 72 |
Si Particle Size-controlled Al-17mass% Si Alloy and Tool Wear in Cutting Al-17mass% Si Alloy by Polycrystalline Diamond Compact Cutting Tool |
T. Wada |
[Accepted in 30 April. 2015, Applied Mechanics and Materials Journal] |
| 73 |
Degradation Behavior of Ca-Mg-Zn Intermetallic Compounds for Use as Biodegradable Implant Materials |
K. Hagihara |
[Materials Science and Engineering C, Vol. 44(2014), pp. 1372 to 1376] |
| 74 |
Selective Laser Melting on Aluminum Foam Surface and Mechanical Properties of Fabricated Aluminum Foam with Nonporous Surface Layer |
R. Matsumoto |
[Key Engineering Materials, Vols. 651-653(2015), pp. 671-676] |
| 75 |
Effect of Crystallographic Texture on Mechanical Properties in Porous Magnesium with Oriented Cylindrical Pores |
M. Tane |
[Acta. Materialia, Vol. 84(2015), pp. 80-94] |
| 76 |
Effects of Stacking Sequence and Short-range Ordering of Solute Atoms on Elastic Properties of Mg-Zn-Y Alloys with long-period Stacking Ordered Structures |
M. Tane |
[Acta. Materialia, Vol. 96(2015), pp. 170-188] |
| 77 |
Improvement of Uniform Elongation by Low Temperature Annealing in Al-2.5%Mg Alloy Processed by Accumulative Roll Bonding |
K. Kashihara |
[Materials Transactions, Vol. 56(2015), pp. 803-807] |
| 78 |
Tensile Properties of AA6061-T6 Friction Stir Welds and Constitutive Modeling in Transverse and Longitudinal Orientations |
K. Nakai |
[Journal of Light Metal Welding, Vol. 53, No. 8(2015), pp. 1-10] |
| 79 |
Image Processing Characterization of Microstructures of Al-Si Casting Alloy |
K. Sugio |
[Materials Science Forum, Vols. 783-786(2014), pp. 240-245] |
| 80 |
Point Defect Clusters Induced by High-speed Deformation and its Effect on Age-hardening in 6061 Aluminum Alloys |
K. Horikawa |
[Materials Science Forum, Vol. 794-796, (2014), pp. 778-783] |
